Bus Bar Ducting Manufacturer Ghaziabad - Electroplating Rectifiers

electroplating-rectifiersElectroplating Rectifiers is an equipment that converts AC into DC supply. Power make Silicon Rectifiers are widely used in Electroplating, Anodizing, Hydrogenation and all other electrochemical processes. These power rectifiers, anodizing rectifiers and electroplating power rectifiers are tailor made, covering a wide range from 200 Amps to 15000 Amps at different output DC voltage as per requirement.

Salient Features

  • Designed for 100% Continuous Duty Cycle
  • Compact Design for Space Saving
  • Lesser Power Consumption
  • Negligible Maintenance
  • Tested at Each & Every Stage of Manufacturing
  • Liberal Design & Rigorous Testing of the Equipment Enables Trouble Free Service for Long Life.
Brief Specifications
Input Voltage 380 - 440 Volts, 3- Phase 50 Hz. AC supply or any other voltage
Output Voltage Fixed Rated maximum DC voltage or variable from zero to maximum rated voltage
Output Current Rated maximum DC current
Temperature Rise Less than 45 C above ambient at the top of the oil
Efficiency Depends on voltage current rating of rectifier
Ripple Content Less than 5%
Insulation 'A' class for oil cooled

Why The Regulator Control Is Superior To Thyristorised Control In Rectifier

  1. electroplating-rectifiers1In plating application the regulator is better and technology is adopted in Germany and Europe because of as explained in advantage.
  2. Other manufacturers of rectifiers have shifted to thyristors because they do not have the technology of rolling carbon roller regulators.
  3. Manufacturers of electroplating power rectifiers claim that thyristor controlled rectifier has less losses than regulator. They compare thyristor with sliding carbon type regulator. In our case their claim is not true. We use vertical coil type rolling carbon regulator. The copper section is three times so the losses are almost 1/6 or 20%.
  4. In our regulator the roller moves on both sides of the coil to give ± 440 V or ± 254 V output. We design the rectifier in 'Q' connection in which the regulator current is half the line current so losses are less and life is much more.

Starting Circuitry

Electroplating Power Rectifiers are designed for 3 phase 50 Hz. AC input supply & are available for operations at any voltage between 380 and 440 volts, in India but can be designed for 60 Hz AC and any other voltage available. It is recommended that the input to the rectifier should be connected through a proper protective device, to provide positive protection to personal and the system, in the event of maintenance or in case a fault occurs. Also manufactures rectifier auto transformer

DC Output Control

The function of the variable output controls is to control the voltage or current or its operating range by varying input voltage to the main transformer primary. The DC output voltage variation is achieved steplessly 0-100% by means of an On Load roller type power make voltage regulator.

Electroplating Power Rectifiers
Basic Circuit of Rectifier
Power Rectifiers
Carbon Roller Assembly Diode

Advantages of Power's Make Roller Type Regulator as Compared to Conventional make Rectifier

Roller Type Regulator
  1. No. wave form distortion at any load, Electrical wave from is like a moving wheel. For 50% Rated Voltage the Dia of wheel is reduced accordingly i.e magnitude for a wave is decreased.
Conventional Make
  1. Wave form distortion in thyrsorised type, It is like cutting the wheel by 50% and then moving the wheel. i.e wave from is cut as shown at full magnitude.
electroplating rectifiers
  1. Higher power factor of more than 98 is achieved .
  2. The system is simple and can be repaired and maintenance even by simple mechanic
  3. The cost of spares is very negligible.
  4. Copper section for particular current is 3 times than conventional make.
  5. Carbon roller rolls on coil and has trouble free life of more than 20 years.
  6. Over all losses are less.
  1. The power factor is lower between 0.5 to 0.75.
  2. The system is specialized and need specially trained Electronic Engineer to repair and maintain
  3. The cost of replacement is very high.
  4. Copper section for particular current in conventional make is 1/3.
  5. Carbon brushes slide on coil, have less life due to sliding on coil & breaks regularly.
  6. Over all losses are more.